7 IP version 4¶
There are multiple LAN protocols below the IP layer and multiple transport protocols above, but IP itself stands alone. The Internet is essentially the IP Internet. If you want to run your own LAN protocol somewhere, or if you want to run your own transport protocol, the Internet backbone will still work just fine for you. But if you want to change the IP layer, you will encounter difficulty. (Just talk to the IPv6 people, or the IP-multicasting or IP-reservations groups.)
Currently the Internet uses (mostly, but no longer quite exclusively) IP version 4, with its 32-bit address size. As the Internet has run out of new large blocks of IPv4 addresses (1.10 IP - Internet Protocol), there is increasing pressure to convert to IPv6, with its 128-bit address size. Progress has been slow, however, and delaying tactics such as IPv4-address markets and NAT (7.7 Network Address Translation) – by which multiple hosts can share a single public IPv4 address – have allowed IPv4 to continue. Aside from the major change in address structure, there are relatively few differences in the routing models of IPv4 and IPv6. We will study IPv4 in this chapter and IPv6 in the following; at points where the IPv4/IPv6 difference doesn’t much matter we will simply write “IP”.
IPv4 (and IPv6) is, in effect, a universal routing and addressing protocol. Routing and addressing are developed together; every node has an IP address and every router knows how to handle IP addresses. IP was originally seen as a way to interconnect multiple LANs, but it may make more sense now to view IP as a virtual LAN overlaying all the physical LANs.
A crucial aspect of IP is its scalability. As the Internet has grown to ~109 hosts, the forwarding tables are not much larger than 105 (perhaps now 105.5). Ethernet, in comparison, scales poorly.
Furthermore, IP, unlike Ethernet, offers excellent support for multiple redundant links. If the network below were an IP network, each node would communicate with each immediate neighbor via their shared direct link. If, on the other hand, this were an Ethernet network with the spanning-tree algorithm, then one of the four links would simply be disabled completely.
The IP network service model is to act like a giant LAN. That is, there are no acknowledgments; delivery is generally described as best-effort. This design choice is perhaps surprising, but it has also been quite fruitful.
If you want to provide a universal service for delivering any packet anywhere, what else do you need besides routing and addressing? Every network (LAN) needs to be able to carry any packet. The protocols spell out the use of octets (bytes), so the only possible compatibility issue is that a packet is too large for a given network. IPv4 handles this by supporting fragmentation: a network may break a too-large packet up into units it can transport successfully. While IPv4 fragmentation is inefficient and clumsy, it does guarantee that any packet can potentially be delivered to any node. (Note, however, that IPv6 has given up on universal fragmentation; 8.5.4 IPv6 Fragment Header.)
7.1 The IPv4 Header¶
The IPv4 Header needs to contain the following information:
- destination and source addresses
- indication of ipv4 versus ipv6
- a Time To Live (TTL) value, to prevent infinite routing loops
- a field indicating what comes next in the packet (eg TCP v UDP)
- fields supporting fragmentation and reassembly.
Here is how it is all laid out in the header. Each row is 32 bits wide.
The IPv4 header, and basics of IPv4 protocol operation, were defined in RFC 791; some minor changes have since occurred. Most of these changes were documented in RFC 1122, though the DS field was defined in RFC 2474 and the ECN bits were first proposed in RFC 2481.
The Version field is, for IPv4, the number 4: 0100. The IHL field represents the total IPv4 Header Length, in 32-bit words; an IPv4 header can thus be at most 15 words long. The base header takes up five words, so the IPv4 Options can consist of at most ten words. If one looks at IPv4 packets using a packet-capture tool that displays the packets in hex, the first byte will most often be 0x45.
The Differentiated Services (DS) field is used by the Differentiated Services suite to specify preferential handling for designated packets, eg those involved in VoIP or other real-time protocols. The Explicit Congestion Notification bits are there to allow routers experiencing congestion to mark packets, thus indicating to the sender that the transmission rate should be reduced. We will address these in 14.8.2 Explicit Congestion Notification (ECN). These two fields together replace the old 8-bit Type of Service field.
The Total Length field is present because an IPv4 packet may be smaller than the minimum LAN packet size (see Exercise 1) or larger than the maximum (if the IPv4 packet has been fragmented over several LAN packets. The IPv4 packet length, in other words, cannot be inferred from the LAN-level packet size. Because the Total Length field is 16 bits, the maximum IPv4 packet size is 216 bytes. This is probably much too large, even if fragmentation were not something to be avoided (though see IPv6 “jumbograms” in 8.5.1 Hop-by-Hop Options Header).
The second word of the header is devoted to fragmentation, discussed below.
The Time-to-Live (TTL) field is decremented by 1 at each router; if it reaches 0, the packet is discarded. A typical initial value is 64; it must be larger than the total number of hops in the path. In most cases, a value of 32 would work. The TTL field is there to prevent routing loops – always a serious problem should they occur – from consuming resources indefinitely. Later we will look at various IP routing-table update protocols and how they minimize the risk of routing loops; they do not, however, eliminate it. By comparison, Ethernet headers have no TTL field, but Ethernet also disallows cycles in the underlying topology.
The Protocol field contains a value to identify the contents of the packet body. A few of the more common values are
- 1: an ICMP packet, 7.11 Internet Control Message Protocol
- 4: an encapsulated IPv4 packet, 7.13.1 IP-in-IP Encapsulation
- 6: a TCP packet
- 17: a UDP packet
- 41: an encapsulated IPv6 packet, 8.13 IPv6 Connectivity via Tunneling
- 50: an Encapsulating Security Payload, 21.11 IPsec
A list of assigned protocol numbers is maintained by the IANA.
The Header Checksum field is the “Internet checksum” applied to the header only, not the body. Its only purpose is to allow the discarding of packets with corrupted headers. When the TTL value is decremented the router must update the header checksum. This can be done “algebraically” by adding a 1 in the correct place to compensate, but it is not hard simply to re-sum the 8 halfwords of the average header. The header checksum must also be updated when an IPv4 packet header is rewritten by a NAT router.
The Source and Destination Address fields contain, of course, the IPv4 addresses. These would normally be updated only by NAT firewalls.
The source-address field is supposed to be the sender’s IPv4 address, but hardly any ISP checks that traffic they send out has a source address matching one of their customers, despite the call to do so in RFC 2827. As a result, IP spoofing – the sending of IP packets with a faked source address – is straightforward. For some examples, see 12.9.1 ISNs and spoofing, and SYN flooding at 12.3 TCP Connection Establishment.
IP-address spoofing also facilitates an all-too-common IP-layer denial-of-service attack in which a server is flooded with a huge volume of traffic so as to reduce the bandwidth available to legitimate traffic to a trickle. This flooding traffic typically originates from a large number of compromised machines. Without spoofing, even a lengthy list of sources can be blocked, but, with spoofing, this becomes quite difficult.
One IPv4 option is the Record Route option, in which routers are to insert their own IPv4 address into the IPv4 header option area. Unfortunately, with only ten words available, there is not enough space to record most longer routes (but see 7.11.1 Traceroute and Time Exceeded, below). The Timestamp option is related; intermediate routers are requested to mark packets with their address and a local timestamp (to save space, the option can request only timestamps). There is room for only four (address,timestamp) pairs, but addresses can be prespecified; that is, the sender can include up to four IPv4 addresses and only those routers will fill in a timestamp.
Another option, now deprecated as security risk, is to support source routing. The sender would insert into the IPv4 header option area a list of IPv4 addresses; the packet would be routed to pass through each of those IPv4 addresses in turn. With strict source routing, the IPv4 addresses had to represent adjacent neighbors; no router could be used if its IPv4 address were not on the list. With loose source routing, the listed addresses did not have to represent adjacent neighbors and ordinary IPv4 routing was used to get from one listed IPv4 address to the next. Both forms are essentially never used, again for security reasons: if a packet has been source-routed, it may have been routed outside of the at-least-somewhat trusted zone of the Internet backbone.
IP addresses (both IPv4 and IPv6) are, strictly speaking, assigned not to hosts or nodes, but to interfaces. In the most common case, where each node has a single LAN interface, this is a distinction without a difference. In a room full of workstations each with a single Ethernet interface
eth0 (or perhaps
Ethernet adapter Local Area Connection), we might as well view the IP address assigned to the interface as assigned to the workstation itself.
Each of those workstations, however, likely also has a loopback interface (at least conceptually), providing a way to deliver IP packets to other processes on the same machine. On many systems, the name “localhost” resolves to the IPv4 address 127.0.0.1 (although the IPv6 address ::1 is also used). Delivering packets to the localhost address is simply a form of interprocess communication; a functionally similar alternative is named pipes. Loopback delivery avoids the need to use the LAN at all, or even the need to have a LAN. For simple client/server testing, it is often convenient to have both client and server on the same machine, in which case the loopback interface is convenient and fast. On unix-based machines the loopback interface represents a genuine logical interface, commonly named
lo. On Windows systems the “interface” may not represent an actual operating-system entity, but this is of practical concern only to those interested in “sniffing” all loopback traffic; packets sent to the loopback address are still delivered as expected.
Workstations often have special other interfaces as well. Most recent versions of Microsoft Windows have a Teredo Tunneling pseudo-interface and an Automatic Tunneling pseudo-interface; these are both intended (when activated) to support IPv6 connectivity when the local ISP supports only IPv4. The Teredo protocol is documented in RFC 4380.
When VPN connections are created, as in 3.1 Virtual Private Networks, each end of the logical connection typically terminates at a virtual interface (one of these is labeled
tun0 in the diagram of 3.1 Virtual Private Networks). These virtual interfaces appear, to the systems involved, to be attached to a point-to-point link that leads to the other end.
When a computer hosts a virtual machine, there is almost always a virtual network to connect the host and virtual systems. The host will have a virtual interface to connect to the virtual network. The host may act as a NAT router for the virtual machine, “hiding” that virtual machine behind its own IP address, or it may act as an Ethernet switch, in which case the virtual machine will need an additional public IP address.
A host with multiple “real” network interfaces is often said to be multihomed (though sometimes multihoming is intended to mean that the different interfaces are on different IP networks; that is, they have different IP prefixes). Many laptops, for example, have both an Ethernet interface and a Wi-Fi interface. Both of these can be used simultaneously, with different IP addresses assigned to each. On residential networks the two interfaces will often be on the same IP network (eg the same bridged Wi-Fi/Ethernet LAN); at more security-conscious sites the Ethernet and Wi-Fi interfaces are often on quite different IP networks (though see 7.9.5 ARP and multihomed hosts).
Routers always have at least two interfaces on two separate IP networks. Generally this means a separate IP address for each interface, though some point-to-point interfaces can be used without being assigned any IP address (7.12 Unnumbered Interfaces).
Finally, it is usually possible to assign multiple IP addresses to a single interface. Sometimes this is done to allow two IP networks to share a single physical LAN; in this case the interface would be assigned one IP address for each IP network. Other times a single interface is assigned multiple IP addresses on the same IP network; this is often done so that one physical machine can act as a server (eg a web server) for multiple distinct IP addresses corresponding to multiple distinct domain names.
While it is important to be at least vaguely aware of all these special cases, we emphasize again that in most ordinary contexts each end-user workstation has one IP address that corresponds to a LAN connection.
7.3 Special Addresses¶
A few IPv4 addresses represent special cases.
While the standard IPv4 loopback address is 127.0.0.1, any IPv4 address beginning with 127 can serve as a loopback address. Logically they all represent the current host. Most hosts are configured to resolve the name “localhost” to 127.0.0.1. However, any loopback address – eg 127.255.33.57 – should work, eg with
Private addresses are IPv4 addresses intended only for site internal use, eg either behind a NAT firewall or intended to have no Internet connectivity at all. If a packet shows up at any non-private router (eg at an ISP router), with a private IPv4 address as either source or destination address, the packet should be dropped. Three standard private-address blocks have been defined:
The last block is the one from which addresses are most commonly allocated by DHCP servers (7.10.1 NAT, DHCP and the Small Office) built into NAT routers.
Broadcast addresses are a special form of IPv4 address intended to be used in conjunction with LAN-layer broadcast. The most common forms are “broadcast to this network”, consisting of all 1-bits, and “broadcast to network D”, consisting of D’s network-address bits followed by all 1-bits for the host bits. If you try to send a packet to the broadcast address of a remote network D, the odds are that some router involved will refuse to forward it, and the odds are even higher that, once the packet arrives at a router actually on network D, that router will refuse to broadcast it. Even addressing a broadcast to ones own network will fail if the underlying LAN does not support LAN-level broadcast (eg ATM).
The highly influential early Unix implementation Berkeley 4.2 BSD used 0-bits for the broadcast bits, instead of 1’s. As a result, to this day host bits cannot be all 1-bits or all 0-bits in order to avoid confusion with the IPv4 broadcast address. One consequence of this is that a Class C network has 254 usable host addresses, not 256.
7.3.1 Multicast addresses¶
Finally, IPv4 multicast addresses remain as the last remnant of the Class A/B/C strategy: multicast addresses are Class D, with first byte beginning 1110 (meaning that the first byte is, in decimal, 224-239). Multicasting means delivering to a specified set of addresses, preferably by some mechanism more efficient than sending to each address individually. A reasonable goal of multicast would be that no more than one copy of the multicast packet traverses any given link.
Support for IPv4 multicast requires considerable participation by the backbone routers involved. For example, if hosts A, B and C each connect to different interfaces of router R1, and A wishes to send a multicast packet to B and C, then it is up to R1 to receive the packet, figure out that B and C are the intended recipients, and forward the packet twice, once for B’s interface and once for C’s. R1 must also keep track of what hosts have joined the multicast group and what hosts have left. Due to this degree of router participation, backbone router support for multicasting has not been entirely forthcoming. A discussion of IPv4 multicasting appears in 19 Quality of Service.
If you are trying to interconnect two LANs (as IP does), what else might be needed besides Routing and Addressing? IPv4 (and IPv6) explicitly assumes all packets are composed on 8-bit bytes (something not universally true in the early days of IP; to this day the RFCs refer to “octets” to emphasize this requirement). IP also defines bit-order within a byte, and it is left to the networking hardware to translate properly. Neither byte size nor bit order, therefore, can interfere with packet forwarding.
There is one more feature IPv4 must provide, however, if the goal is universal connectivity: it must accommodate networks for which the maximum packet size, or Maximum Transfer Unit, MTU, is smaller than the packet that needs forwarding. Otherwise, if we were using IPv4 to join Token Ring (MTU = 4KB, at least originally) to Ethernet (MTU = 1500B), the token-ring packets might be too large to deliver to the Ethernet side, or to traverse an Ethernet backbone en route to another Token Ring. (Token Ring, in its day, did commonly offer a configuration option to allow Ethernet interoperability.)
So, IPv4 must support fragmentation, and thus also reassembly. There are two potential strategies here: per-link fragmentation and reassembly, where the reassembly is done at the opposite end of the link (as in ATM), and path fragmentation and reassembly, where reassembly is done at the far end of the path. The latter approach is what is taken by IPv4, partly because intermediate routers are too busy to do reassembly (this is as true today as it was in 1981 when RFC 791 was published), partly because there is no absolute guarantee that all fragments will go to the same next-hop router, and partly because IPv4 fragmentation has always been seen as the strategy of last resort.
An IPv4 sender is supposed to use a different value for the IDENT field for different packets, at least up until the field wraps around. When an IPv4 datagram is fragmented, the fragments keep the same IDENT field, so this field in effect indicates which fragments belong to the same packet.
After fragmentation, the Fragment Offset field marks the start position of the data portion of this fragment within the data portion of the original IPv4 packet. Note that the start position can be a number up to 216, the maximum IPv4 packet length, but the FragOffset field has only 13 bits. This is handled by requiring the data portions of fragments to have sizes a multiple of 8 (three bits), and left-shifting the FragOffset value by 3 bits before using it.
As an example, consider the following network, where MTUs are excluding the LAN header:
Suppose A addresses a packet of 1500 bytes to B, and sends it via the LAN to the first router R1. The packet contains 20 bytes of IPv4 header and 1480 of data.
R1 fragments the original packet into two packets of sizes 20+976 = 996 and 20+504=544. Having 980 bytes of payload in the first fragment would fit, but violates the rule that the sizes of the data portions be divisible by 8. The first fragment packet has FragOffset = 0; the second has FragOffset = 976.
R2 refragments the first fragment into three packets as follows:
- first: size = 20+376=396, FragOffset = 0
- second: size = 20+376=396, FragOffset = 376
- third: size = 20+224 = 244 (note 376+376+224=976), FragOffset = 752.
R2 refragments the second fragment into two:
- first: size = 20+376 = 396, FragOffset = 976+0 = 976
- second: size = 20+128 = 148, FragOffset = 976+376=1352
R3 then sends the fragments on to B, without reassembly.
Note that it would have been slightly more efficient to have fragmented into four fragments of sizes 376, 376, 376, and 352 in the beginning. Note also that the packet format is designed to handle fragments of different sizes easily. The algorithm is based on multiple fragmentation with reassembly only at the final destination.
Each fragment has its IPv4-header Total Length field set to the length of that fragment.
We have not yet discussed the three flag bits. The first bit is reserved, and must be 0. The second bit is the Don’t Fragment, or DF, bit. If it is set to 1 by the sender then a router must not fragment the packet and must drop it instead; see 12.12 Path MTU Discovery for an application of this. The third bit is set to 1 for all fragments except the final one (this bit is thus set to 0 if no fragmentation has occurred). The third bit tells the receiver where the fragments stop.
The receiver must take the arriving fragments and reassemble them into a whole packet. The fragments may not arrive in order – unlike in ATM networks – and may have unrelated packets interspersed. The reassembler must identify when different arriving packets are fragments of the same original, and must figure out how to reassemble the fragments in the correct order; both these problems were essentially trivial for ATM.
Fragments are considered to belong to the same packet if they have the same IDENT field and also the same source and destination addresses and same protocol.
As all fragment sizes are a multiple of 8 bytes, the receiver can keep track of whether all fragments have been received with a bitmap in which each bit represents one 8-byte fragment chunk. A 1 KB packet could have up to 128 such chunks; the bitmap would thus be 16 bytes.
If a fragment arrives that is part of a new (and fragmented) packet, a buffer is allocated. While the receiver cannot know the final size of the buffer, it can usually make a reasonable guess. Because of the FragOffset field, the fragment can then be stored in the buffer in the appropriate position. A new bitmap is also allocated, and a reassembly timer is started.
As subsequent fragments arrive, not necessarily in order, they too can be placed in the proper buffer in the proper position, and the appropriate bits in the bitmap are set to 1.
If the bitmap shows that all fragments have arrived, the packet is sent on up as a completed IPv4 packet. If, on the other hand, the reassembly timer expires, then all the pieces received so far are discarded.
TCP connections usually engage in Path MTU Discovery, and figure out the largest packet size they can send that will not entail fragmentation (12.12 Path MTU Discovery). But it is not unusual, for example, for UDP protocols to use fragmentation, especially over the short haul. In the Network File Sharing (NFS) protocol, for example, UDP is used to carry 8KB disk blocks. These are often sent as a single 8+ KB IPv4 packet, fragmented over Ethernet to five full packets and a fraction. Fragmentation works reasonably well here because most of the time the packets do not leave the Ethernet they started on. Note that this is an example of fragmentation done by the sender, not by an intermediate router.
Finally, any given IP link may provide its own link-layer fragmentation and reassembly; we saw in 3.5.1 ATM Segmentation and Reassembly that ATM does just this. Such link-layer mechanisms are, however, generally invisible to the IP layer.
7.5 The Classless IP Delivery Algorithm¶
Recall from Chapter 1 that any IPv4 address can be divided into a net portion IPnet and a host portion IPhost; the division point was determined by whether the IPv4 address was a Class A, a Class B, or a Class C. We also indicated in Chapter 1 that the division point was not always so clear-cut; we now present the delivery algorithm, for both hosts and routers, that does not assume a globally predeclared division point of the input IPv4 address into net and host portions. We will, for the time being, punt on the question of forwarding-table lookup and assume there is a
lookup() method available that, when given a destination address, returns the next_hop neighbor.
Instead of class-based divisions, we will assume that each of the IPv4 addresses assigned to a node’s interfaces is configured with an associated length of the network prefix; following the slash notation of 1.10 IP - Internet Protocol, if B is an address and the prefix length is k = kB then the prefix itself is B/k. As usual, an ordinary host may have only one IP interface, while a router will always have multiple interfaces.
Let D be the given IPv4 destination address; we want to decide if D is local or nonlocal. The host or router involved may have multiple IP interfaces, but for each interface the length of the network portion of the address will be known. For each network address B/k assigned to one of the host’s interfaces, we compare the first k bits of B and D; that is, we ask if D matches B/k.
- If one of these comparisons yields a match, delivery is local; the host delivers the packet to its final destination via the LAN connected to the corresponding interface. This means looking up the LAN address of the destination, if applicable, and sending the packet to that destination via the interface.
- If there is no match, delivery is nonlocal, and the host passes D to the
lookup()routine of the forwarding table and sends to the associated next_hop (which must represent a physically connected neighbor). It is now up to
lookup()routine to make any necessary determinations as to how D might be split into Dnet and Dhost; the split cannot be made outside of
The forwarding table is, abstractly, a set of network addresses – now also with lengths – each of the form B/k, with an associated next_hop destination for each. The
lookup() routine will, in principle, compare D with each table entry B/k, looking for a match (that is, equality of the first k = kB bits). As with the local-delivery interfaces check above, the net/host division point (that is, k) will come from the table entry; it will not be inferred from D or from any other information borne by the packet. There is, in fact, no place in the IPv4 header to store a net/host division point, and furthermore different routers along the path may use different values of k with the same destination address D. Routers receive the prefix length /k for a destination B/k as part of the process by which they receive (destination,next_hop) pairs; see 9 Routing-Update Algorithms.
In 10 Large-Scale IP Routing we will see that in some cases multiple matches in the forwarding table may exist, eg 18.104.22.168/8 and 22.214.171.124/16. The longest-match rule will be introduced for such cases to pick the best match.
Here is a simple example for a router with immediate neighbors A-E:
The IPv4 addresses 10.3.67.101 and 10.3.59.131 both route to A. The addresses 10.4.1.101, 10.4.2.157 and 10.4.3.233 route to B, C and D respectively. Finally, 10.3.37.103 matches both A and E, but the E match is longer so the packet is routed that way.
The forwarding table may also contain a default entry for the next_hop, which it may return in cases when the destination D does not match any known network. We take the view here that returning such a default entry is a valid result of the routing-table
lookup() operation, rather than a third option to the algorithm above; one approach is for the default entry to be the next_hop corresponding to the destination 0.0.0.0/0, which does indeed match everything (use of this would definitely require the above longest-match rule, though).
Default routes are hugely important in keeping leaf forwarding tables small. Even backbone routers sometimes expend considerable effort to keep the network address prefixes in their forwarding tables as short as possible, through consolidation.
At a site with a single ISP and with no Internet customers (that is, which is not itself an ISP for others), the top-level forwarding table usually has a single external route: its default route to its ISP. If a site has more than one ISP, however, the top-level forwarding table can expand in a hurry. For example, Internet2 is a consortium of research sites with very-high-bandwidth internal interconnections, acting as a sort of “parallel Internet”. Before Internet2, Loyola’s top-level forwarding table had the usual single external default route. After Internet2, we in effect had a second ISP and had to divide traffic between the commercial ISP and the Internet2 ISP. The default route still pointed to the commercial ISP, but the top-level forwarding table now had to have an entry for every individual Internet2 site, so that traffic to any of these sites would be forwarded via the Internet2 ISP. See exercise 5.0.
Routers may also be configured to allow passing quality-of-service information to the
lookup() method, as mentioned in Chapter 1, to support different routing paths for different kinds of traffic (eg bulk file-transfer versus real-time).
For a modest exception to the local-delivery rule described here, see below in 7.12 Unnumbered Interfaces.
7.6 IPv4 Subnets¶
Subnets were the first step away from Class A/B/C routing: a large network (eg a class A or B) could be divided into smaller IPv4 networks called subnets. Consider, for example, a typical Class B network such as Loyola University’s (originally 126.96.36.199/16); the underlying assumption is that any packet can be delivered via the underlying LAN to any internal host. This would require a rather large LAN, and would require that a single physical LAN be used throughout the site. What if our site has more than one physical LAN? Or is really too big for one physical LAN? It did not take long for the IP world to run into this problem.
Getting a separate IPv4 network prefix for each subnet is bad for routers: the backbone forwarding tables now must have an entry for every subnet instead of just for every site. What is needed is a way for a site to appear to the outside world as a single IP network, but for further IP-layer routing to be supported inside the site. This is what subnets accomplish.
Subnets introduce hierarchical routing: first we route to the primary network, then inside that site we route to the subnet, and finally the last hop delivers to the host.
Routing with subnets involves in effect moving the IPnet division line rightward. (Later, when we consider CIDR, we will see the complementary case of moving the division line to the left.) For now, observe that moving the line rightward within a site does not affect the outside world at all; outside routers are not even aware of site-internal subnetting.
In the following diagram, the outside world directs traffic addressed to 188.8.131.52/16 to the router R. Internally, however, the site is divided into subnets. The idea is that traffic from 184.108.40.206/24 to 220.127.116.11/24 is routed, not switched; the two LANs involved may not even be compatible. Most of the subnets shown are of size /24, meaning that the third byte of the IPv4 address has become part of the network portion of the subnet’s address; one /20 subnet is also shown. RFC 950 would have disallowed the subnet with third byte 0, but having 0 for the subnet bits generally does work.
What we want is for the internal routing to be based on the extended network prefixes shown, while externally continuing to use only the single routing entry for 18.104.22.168/16.
To implement subnets, we divide the site’s IPv4 network into some combination of physical LANs – the subnets –, and assign each a subnet address: an IPv4 network address which has the site’s IPv4 network address as prefix. To put this more concretely, suppose the site’s IPv4 network address is A, and consists of n network bits (so the site address may be written with the slash notation as A/n); in the diagram above, A/n = 22.214.171.124/16. A subnet address is an IPv4 network address B/k such that:
- The address B/k is within the site: the first n bits of B are the same as A/n’s
- B/k extends A/n: k≥n
An example B/k in the diagram above is 126.96.36.199/24. (There is a slight simplification here in that subnet addresses do not absolutely have to be prefixes; see below.)
We now have to figure out how packets will be routed to the correct subnet. For incoming packets we could set up some proprietary protocol at the entry router to handle this. However, the more complicated situation is all those existing internal hosts that, under the class A/B/C strategy, would still believe they can deliver via the LAN to any site host, when in fact they can now only do that for hosts on their own subnet. We need a more general solution.
We proceed as follows. For each subnet address B/k, we create a subnet mask for B consisting of k 1-bits followed by enough 0-bits to make a total of 32. We then make sure that every host and router in the site knows the subnet mask for every one of its interfaces. Hosts usually find their subnet mask the same way they find their IP address (by static configuration if necessary, but more likely via DHCP, below).
Hosts and routers now apply the IP delivery algorithm of the previous section, with the proviso that, if a subnet mask for an interface is present, then the subnet mask is used to determine the number of address bits rather than the Class A/B/C mechanism. That is, we determine whether a packet addressed to destination D is deliverable locally via an interface with subnet address B/k and corresponding mask M by comparing D&M with B&M, where & represents bitwise AND; if the two match, the packet is local. This will generally involve a match of more bits than if we used the Class A/B/C strategy to determine the network portion of addresses D and B.
As stated previously, given an address D with no other context, we will not be able to determine the network/host division point in general (eg for outbound packets). However, that division point is not in fact what we need. All that is needed is a way to tell if a given destination host address D belongs to the current subnet, say B; that is, we need to compare the first k bits of D and B where k is the (known) length of B.
In the diagram above, the subnet mask for the /24 subnets would be 255.255.255.0; bitwise ANDing any IPv4 address with the mask is the same as extracting the first 24 bits of the IPv4 address, that is, the subnet portion. The mask for the /20 subnet would be 255.255.240.0 (240 in binary is 1111 0000).
In the diagram above none of the subnets overlaps or conflicts: the subnets 188.8.131.52/24 and 184.108.40.206/24 are disjoint. It takes a little more effort to realize that 220.127.116.11/20 does not overlap with the others, but note that an IPv4 address matches this network prefix only if the first four bits of the third byte are 0001, so the third byte itself ranges from decimal 32 to decimal 63 = binary 0001 1111.
Note also that if host A = 18.104.22.168 wishes to send to destination D = 22.214.171.124, and A is not subnet-aware, then delivery will fail: A will infer that the interface is a Class B, and therefore compare the first two bytes of A and D, and, finding a match, will attempt direct LAN delivery. But direct delivery is now likely impossible, as the subnets are not joined by a switch. Only with the subnet mask will A realize that its network is 126.96.36.199/24 while D’s is 188.8.131.52/24 and that these are not the same. A would still be able to send packets to its own subnet. In fact A would still be able to send packets to the outside world: it would realize that the destination in that case does not match 184.108.40.206/16 and will thus forward to its router. Hosts on other subnets would be the only unreachable ones.
Properly, the subnet address is the entire prefix, eg 220.127.116.11/24. However, it is often convenient to identify the subnet address with just those bits that represent the extension of the site IPv4-network address; we might thus say casually that the subnet address here is 65.
The class-based IP-address strategy allowed any host anywhere on the Internet to properly separate any address into its net and host portions. With subnets, this division point is now allowed to vary; for example, the address 18.104.22.168 divides into 147.126 | 65.48 outside of Loyola, but into 147.126.65 | 48 inside. This means that the net-host division is no longer an absolute property of addresses, but rather something that depends on where the packet is on its journey.
Technically, we also need the requirement that given any two subnet addresses of different, disjoint subnets, neither is a proper prefix of the other. This guarantees that if A is an IP address and B is a subnet address with mask M (so B = B&M), then A&M = B implies A does not match any other subnet. Regardless of the net/host division rules, we cannot possibly allow subnet 22.214.171.124/20 to represent one LAN while 126.96.36.199/24 represents another; the second subnet address block is a subset of the first. (We can, and sometimes do, allow the first LAN to correspond to everything in 188.8.131.52/20 that is not also in 184.108.40.206/24; this is the longest-match rule.)
The strategy above is actually a slight simplification of what the subnet mechanism actually allows: subnet address bits do not in fact have to be contiguous, and masks do not have to be a series of 1-bits followed by 0-bits. The mask can be any bit-mask; the subnet address bits are by definition those where there is a 1 in the mask bits. For example, we could at a Class-B site use the fourth byte as the subnet address, and the third byte as the host address. The subnet mask would then be 255.255.0.255. While this generality was once sometimes useful in dealing with “legacy” IPv4 addresses that could not easily be changed, life is simpler when the subnet bits precede the host bits.
7.6.1 Subnet Example¶
As an example of having different subnet masks on different interfaces, let us consider the division of a class-C network into subnets of size 70, 40, 25, and 20. The subnet addresses will of necessity have different lengths, as there is not room for four subnets each able to hold 70 hosts.
- A: size 70
- B: size 40
- C: size 25
- D: size 20
Because of the different subnet-address lengths, division of a local IPv4 address LA into net versus host on subnets cannot be done in isolation, without looking at the host bits. However, that division is not in fact what we need. All that is needed is a way to tell if the local address LA belongs to a given subnet, say B; that is, we need to compare the first n bits of LA and B, where n is the length of B’s subnet mask. We do this by comparing LA&M to B&M, where M is the mask corresponding to n. LA&M is not necessarily the same as LAnet, if LA actually belongs to one of the other subnets. However, if LA&M = B&M, then LA must belong subnet B, in which case LA&M is in fact LAnet.
We will assume that the site’s IPv4 network address is 220.127.116.11/24. The first three bytes of each subnet address must match 200.0.0. Only some of the bits of the fourth byte will be part of the subnet address, so we will switch to binary for the last byte, and use both the /n notation (for total number of subnet bits) and also add a vertical bar | to mark the separation between subnet and host.
Example: 18.104.22.168 | 00 0000 / 26
Note that this means that the 0-bit following the 1-bit in the fourth byte is “significant” in that for a subnet to match, it must match this 0-bit exactly. The remaining six 0-bits are part of the host portion.
To allocate our four subnet addresses above, we start by figuring out just how many host bits we need in each subnet. Subnet sizes are always powers of 2, so we round up the subnets to the appropriate size. For subnet A, this means we need 7 host bits to accommodate 27 = 128 hosts, and so we have a single bit in the fourth byte to devote to the subnet address. Similarly, for B we will need 6 host bits and will have 2 subnet bits, and for C and D we will need 5 host bits each and will have 8-5=3 subnet bits.
We now start choosing non-overlapping subnet addresses. We have one bit in the fourth byte to choose for A’s subnet; rather arbitrarily, let us choose this bit to be 1. This means that every other subnet address must have a 0 in the first bit position of the fourth byte, or we would have ambiguity.
Now for B’s subnet address. We have two bits to work with, and the first bit must be 0. Let us choose the second bit to be 0 as well. If the fourth byte begins 00, the packet is part of subnet B, and the subnet addresses for C and D must therefore not begin 00.
Finally, we choose subnet addresses for C and D to be 010 and 011, respectively. We thus have
|subnet||size||address bits in fourth byte||host bits in 4th byte||decimal range|
As desired, none of the subnet addresses in the third column is a prefix of any other subnet address.
The end result of all of this is that routing is now hierarchical: we route on the site IP address to get to a site, and then route on the subnet address within the site.
7.6.3 Subnets versus Switching¶
A frequent network design question is whether to have many small subnets or to instead have just a few (or even only one) larger subnet. With multiple small subnets, IP routing would be used to interconnect them; the use of larger subnets would replace much of that routing with LAN-layer communication, likely Ethernet switching. Debates on this route-versus-switch question have gone back and forth in the networking community, with one aphorism summarizing a common view:
Switch when you can, route when you must
This aphorism reflects the idea that switching is faster, cheaper and easier to configure, and that subnet boundaries should be drawn only where “necessary”.
Ethernet switching equipment is indeed generally cheaper than routing equipment, for the same overall level of features and reliability. And traditional switching requires relatively little configuration, while to implement subnets not only must the subnets be created by hand but one must also set up and configure the routing-update protocols. However, the price difference between switching and routing is not always significant in the big picture, and the configuration involved is often straightforward.
Somewhere along the way, however, switching has acquired a reputation – often deserved – for being faster than routing. It is true that routers have more to do than switches: they must decrement TTL, update the header checksum, and attach a new LAN header. But these things are relatively minor: a larger reason many routers are slower than switches may simply be that they are inevitably asked to serve as firewalls. This means “deep inspection” of every packet, eg comparing every packet to each of a large number of firewall rules. The firewall may also be asked to keep track of connection state. All this drives down the forwarding rate, as measured in packets-per-second.
Traditional switching scales remarkably well, but it does have limitations. First, broadcast packets must be forwarded throughout a switched network; they do not, however, pass to different subnets. Second, LAN networks do not like redundant links (that is, loops); while one can rely on the spanning-tree algorithm to eliminate these, that algorithm too becomes less efficient at larger scales.
The rise of software-defined networking (2.7 Software-Defined Networking) has blurred the distinction between routing and switching. The term “Layer 3 switch” is sometimes used to describe routers that in effect do not support all the usual firewall bells and whistles. These are often SDN Ethernet switches (2.7 Software-Defined Networking) that are making forwarding decisions based on the contents of the IP header. Such streamlined switch/routers may also be able to do most of the hard work in specialized hardware, another source of speedup.
But SDN can do much more than IP-layer forwarding, by taking advantage of site-specific layout information. One application, of a switch hierarchy for traffic entering a datacenter, appears in 2.7.1 OpenFlow Switches. Other SDN applications include enabling Ethernet topologies with loops, offloading large-volume flows to alternative paths, and implementing policy-based routing as in 9.6 Routing on Other Attributes. Some SDN solutions involve site-specific programming, but others work more-or-less out of the box. Locations with switch-versus-route issues are likely to turn increasingly to SDN in the future.
7.7 Network Address Translation¶
What do you do if your ISP assigns to you a single IPv4 address and you have two computers? The solution is Network Address Translation, or NAT. NAT’s ability to “multiplex” an arbitrarily large number of individual hosts behind a single IPv4 address (or small number of addresses) makes it an important tool in the conservation of IPv4 addresses. It also, however, enables an important form of firewall-based security. It is documented in RFC 3022, where this is called NAPT, or Network Address Port Translation.
The basic idea is that, instead of assigning each host at a site a publicly visible IPv4 address, just one such address is assigned to a special device known as a NAT router. A NAT router sold for residential or small-office use is commonly simply called a “router”, or (somewhat more precisely) a “residential gateway”. One side of the NAT router connects to the Internet; the other connects to the site’s internal network. Hosts on the internal network are assigned private IP addresses (7.3 Special Addresses), typically of the form or 192.168.x.y or 10.x.y.z. Connections to internal hosts that originate in the outside world are banned. When an internal machine wants to connect to the outside, the NAT router intercepts the connection, and forwards the connection’s packets after rewriting the source address to make it appear they came from the NAT router’s own IP address, shown below as 22.214.171.124.
The remote machine responds, sending its responses to the NAT router’s public IPv4 address. The NAT router remembers the connection, having stored the connection information in a special forwarding table, and forwards the data to the correct internal host, rewriting the destination-address field of the incoming packets.
The NAT forwarding table also includes port numbers. That way, if two internal hosts attempt to connect to the same external host, the NAT router can tell which packets belong to which. For example, suppose internal hosts A and B each connect from port 3000 to port 80 on external hosts S and T, respectively. Here is what the NAT forwarding table might look like. No columns for the NAT router’s own IPv4 addresses are needed; we shall let NR denote the router’s external address.
|remote host||remote port||outside source port||inside host||inside port|
A packet to S from (A,3000) would be rewritten so that the source was (NR,3000). A packet from (S,80) addressed to (NR,3000) would be rewritten and forwarded to (A,3000). Similarly, a packet from (T,80) addressed to (NR,3000) would be rewritten and forwarded to (B,3000); the NAT table takes into account the source host and port as well as the destination.
Sometimes it is necessary for the NAT router to rewrite the internal-side port number as well; this happens if two internal hosts want to connect, each from the same port, to the same external host and port. For example, suppose B now opens a connection to (S,80), also from inside port 3000. This time the NAT router must remap the port number, because that is the only way to distinguish between packets from (S,80) back to A and to B. With B’s second connection’s internal port remapped from 3000 to 3001, the new table is
|remote host||remote port||outside source port||inside host||inside port|
The NAT router does not create TCP connections between itself and the external hosts; it simply forwards packets (with rewriting). The connection endpoints are still the external hosts S and T and the internal hosts A and B. However, NR might very well monitor the TCP connections to know when they have closed, and so can be removed from the table. For UDP connections, NAT routers typically remove the forwarding entry after some period of inactivity; see 11 UDP Transport, exercise 14.0.
NAT still works for some traffic without port numbers, such as network pings, though the above table is then not quite the whole story. See 7.11 Internet Control Message Protocol.
Done properly, NAT improves the security of a site, by making it impossible for an external host to probe or connect to any of the internal hosts. While this firewall feature is of great importance, essentially the same effect can be achieved without address translation, and with public IPv4 addresses for all internal hosts, by having the router refuse to forward incoming packets that are not part of existing connections. The router still needs to maintain a table like the NAT table above, in order to recognize such packets. The address translation itself, in other words, is not the source of the firewall security. That said, it is hard for a NAT router to “fail open”; ie to fail in a way that lets outside connections in. It is much easier for a non-NAT firewall to fail open.
For the common residential form of NAT router, see 7.10.1 NAT, DHCP and the Small Office.
7.7.1 NAT Problems¶
NAT router’s refusal to allow inbound connections is a source of occasional frustration. We illustrate some of these frustrations here, using Voice-over-IP (VoIP) and the call-setup protocol SIP (RFC 3261). The basic strategy is that each phone is associated with a remote phone server. These phone servers, because they have to be able to accept incoming connections from anywhere, must not be behind NAT routers. The phones themselves, however, usually will be:
For phone1 to call phone2, phone1 first contacts Server1, which then contacts Server2. So far, all is well. The final step is for Server2 to contact phone2, which, however, cannot be done normally as NAT2 allows no inbound connections.
One common solution is for phone2 to maintain a persistent connection to Server2 (and ditto for phone1 and Server1). By having these persistent phone-to-server connections, we can arrange for the phone to ring on incoming calls.
As a second issue, somewhat particular to the SIP protocol, is that it is common for server and phone to prefer to use UDP port 5060 at both ends. For a single internal phone, it is likely that port 5060 will pass through without remapping, so the phone will appear to be connecting from the desired port 5060. However, if there are two phones inside (not shown above), one of them will appear to be connecting to the server from an alternative port. The solution here is to have the server tolerate such port remapping.
VoIP systems run into a much more serious problem with NAT, however. Once the call between phone1 and phone2 is set up, the servers would prefer to step out of the loop, and have the phones exchange voice packets directly. The SIP protocol was designed to handle this by having each phone report to its respective server the UDP socket ((IP address,port) pair) it intends to use for the voice exchange; the servers then report these phone sockets to each other, and from there to the opposite phones. This socket information is rendered incorrect by NAT, however, certainly the IP address and quite likely the port as well. If only one of the phones is behind a NAT firewall, it can initiate the voice connection to the other phone, but the other phone will see the voice packets arriving from a different socket than promised and will likely not recognize them as part of the call. If both phones are behind NAT firewalls, they will not be able to connect directly to one another at all. The common solution is for the VoIP server of a phone behind a NAT firewall to remain in the communications path, forwarding packets to its hidden partner. This works, but represents an unwanted server workload.
If a site wants to make it possible to allow external connections to hosts behind a NAT router or other firewall, one option is tunneling. This is the creation of a “virtual LAN link” that runs on top of a TCP connection between the end user and one of the site’s servers; the end user can thus appear to be on one of the organization’s internal LANs; see 3.1 Virtual Private Networks. Another option is to “open up” a specific port: in essence, a static NAT-table entry is made connecting a specific port on the NAT router to a specific internal host and port (usually the same port). For example, all UDP packets to port 5060 on the NAT router might be forwarded to port 5060 on internal host A, even in the absence of any prior packet exchange. Gamers creating peer-to-peer game connections must also usually engage in some port-opening configuration. The Port Control Protocol (RFC 6887) is sometimes used for this.
NAT routers work very well when the communications model is of client-side TCP connections, originating from the inside and with public outside servers as destination. The NAT model works less well for peer-to-peer networking, as with the gamers above, where two computers, each behind a different NAT router, wish to establish a connection. NAT routers also often have trouble with UDP protocols, due to the tendency for such protocols to have the public server reply from a different port than the one originally contacted. For example, if host A behind a NAT router attempts to use TFTP (11.2 Trivial File Transport Protocol, TFTP), and sends a packet to port 69 of public server C, then C is likely to reply from some new port, say 3000, and this reply is likely to be dropped by the NAT router as there will be no entry there yet for traffic from (C,3000).
The Domain Name System, DNS, is an essential companion protocol to IPv4; an overview can be found in RFC 1034. It is DNS that permits users the luxury of not needing to remember numeric IP addresses. Instead of 126.96.36.199, a user can simply enter intronetworks.cs.luc.edu, and DNS will take care of looking up the name and finding the corresponding address. DNS also makes it easy to move services from one server to another with a different IP address; as users will locate the service by DNS name and not by IP address, they do not need to be notified.
While a workstation can use TCP/IP without DNS, users have an almost impossible time finding anything, and so the core startup configuration of an Internet-connected workstation almost always includes the IP address of its DNS server (see 7.10 Dynamic Host Configuration Protocol (DHCP) below for how startup configurations are often assigned).
Most DNS traffic today is over UDP, although a TCP option exists.
DNS is distributed, meaning that each domain is responsible for maintaining its own DNS servers to translate names to addresses. (DNS, in fact, is a classic example of a highly distributed database where each node maintains a relatively small amount of data.) It is hierarchical as well; for the DNS name
intronetworks.cs.luc.edu the levels of the hierarchy are
- edu: the top-level domain (TLD) for educational institutions in the US
- luc: Loyola University Chicago
- cs: The Loyola Computer Science Department
- intronetworks: a hostname associated to a specific IP address
The hierarchy of DNS names (that is, the set of all names and prefixes of names) forms a tree, but it is not only leaf nodes that represent individual hosts. In the example above, luc.edu and cs.luc.edu happen to be valid hostnames as well.
Top-level domains are assigned by ICANN. The original top-level domains were the two-letter country-code domains (eg .us, .ca, .mx) and seven others:
.gov. Now there are hundreds of non-country top-level domains.
The full tree of all DNS names and prefixes is divided administratively into zones: a zone is a subtree, minus any sub-subtrees that have been placed – by delegation – into their own zone. Each zone has its own root DNS name that is a prefix of every DNS name in the zone. For example, the
luc.edu zone contains most of Loyola’s DNS names, but
cs.luc.edu has been spun off into its own zone. A zone cannot be the disjoint union of two subtrees.
Each zone has its own authoritative nameservers for the zone, which are charged with maintaining the records for that zone. Each zone must have at least two nameservers, for redundancy. IPv4 addresses are stored as so-called A records, for Address. Information about how to find sub-zones is stored as NS records. An authoritative nameserver need not be part of the organization that manages the zone, and a single server can be the authoritative nameserver for thousands of unrelated zones.
The root nameservers handle the zone that is the root of the DNS tree; that is, that is represented by the DNS name that is the empty string. The root nameservers contain only NS records, identifying the nameservers for all the immediate subzones. Each top-level domain is its own such subzone. The IP addresses of the root nameservers are widely distributed. Their DNS names (which are only of use if some DNS lookup mechanism is already present) are
m.root-servers.net. These names today correspond not to individual machines but to clusters of up to hundreds of servers.
We can now put together a first draft of a DNS lookup algorithm. To find the IP address of intronetworks.cs.luc.edu, a host first contacts a root nameserver (at a known address) to find the nameserver for the
edu zone; this involves the retrieval of an NS record. The
edu nameserver is then queried to find the nameserver for the
luc.edu zone, which in turn supplies the NS record giving the address of the
cs.luc.edu zone. This last has an A record for the actual host. (This example is carried out in detail below.)
This strategy has a defect in that it would send much too much traffic to the root nameservers. Instead, it is common for each organization or ISP to provide what we will call a resolver (though, confusingly, these are sometimes also known as “nameservers” or, more precisely, non-authoritative nameservers). A resolver is a nearby host charged with looking up DNS names on behalf of the site’s users or customers, and returning corresponding addresses. It uses the algorithm of the previous paragraph as a fallback, but also keeps a large cache of all the domain names that have been requested. A lifetime for each cache entry is provided by that entry’s authoritative nameserver; these lifetimes are typically on the order of several days. If I send a query to Loyola’s resolver for
google.com, it is almost certainly in the cache. If I send a query for the misspelling googel.com, this may not be in the cache, but the
.com top-level nameserver almost certainly is in the cache. From that nameserver my local resolver finds the nameserver for the
googel.com zone, and from that finds the IP address of the
At the DNS protocol layer, a DNS lookup query can be either recursive or non-recursive. If A sends to B a recursive query to resolve a given DNS name, then B takes over the job until it is finally able to return an answer to A. If The query is non-recursive, on the other hand, then if B is not an authoritative nameserver for the DNS name in question it returns either a failure notice or an NS record for the sub-zone that is the next step on the path.
Applications almost always invoke DNS through library calls, such as Java’s
InetAddress.getByName(). The library forwards the query to the designated resolver. We will return to this in 188.8.131.52 The Client and 12.5.1 The TCP Client.
Usually a DNS lookup of a hostname returns a single A record, representing a single IPv4 address. If a site has multiple servers that are entirely equivalent, however, it is possible to give them all the same hostname by configuring the authoritative nameserver to return, for the hostname in question, multiple A records listing, in turn, each of the server IPv4 addresses. This is sometimes known as round-robin DNS. Consecutive queries to the nameserver should return the list of A records in different orders; ideally the same should also happen with consecutive queries to a local resolver that has the hostname in its cache. It is also common for a single server, with a single IPv4 address, to be identified by multiple DNS names; see the next section.
The Tor Project uses DNS-like names that end in ”.onion”. While these are not true DNS names in that they are not managed by the DNS hierarchy, they do work as such for Tor users; see RFC 7686. These names follow an unusual pattern: the next level of name is an 80-bit hash of the site’s RSA public key (21.9.1 RSA), converted to sixteen ASCII bytes. For example, 3g2upl4pq6kufc4m.onion is apparently the Tor address for the search engine duckduckgo.com. Unlike DuckDuckGo, many sites try different RSA keys until they find one where at least some initial prefix of the hash looks more or less meaningful. Facebook got very lucky in finding an RSA key whose corresponding Tor address is
facebookcorewwwi.onion (though it is sometimes said that fortune is infatuated with the wealthy). This naming strategy is a form of cryptographically generated addresses; for another example see 8.6.4 Security and Neighbor Discovery. The advantage of this naming strategy is that you don’t need a certificate authority (184.108.40.206 Certificate Authorities) to verify a site’s RSA key; the site name does it for you.
Let us trace a non-recursive lookup of
intronetworks.cs.luc.edu, using the nslookup tool. Lines we type in
nslookup‘s interactive mode begin below with the prompt “>”; the shell prompt is “#”.
The first step is to look up the IP address of the root nameserver
a.name-servers.net. We can do this with a regular call to
nslookup, we can look this up in our nameserver’s configuration files, or we can search for it on the Internet. The address is 220.127.116.11.
We now send our nonrecursive query to this address; the presence of the single hyphen in the command line below means that we want to use 18.104.22.168 as the nameserver rather than as the thing to be looked up:
# nslookup -norecurse - 22.214.171.124 > intronetworks.cs.luc.edu *** Can't find intronetworks.cs.luc.edu: No answer
This is because by default
nslookup asks for an A record. What we want is an NS record: the name of the next zone down to ask.
> set query=ns > intronetworks.cs.luc.edu edu nameserver = a.edu-servers.net ... a.edu-servers.net internet address = 126.96.36.199
This is one of the nameservers for the .edu zone. (We also get back several other edu-servers.)
We send the next NS query to a.edu-servers.net:
# nslookup -query=ns -norecurse - 188.8.131.52 > intronetworks.cs.luc.edu ... Authoritative answers can be found from: luc.edu nameserver = bcdnswt1.it.luc.edu. bcdnswt1.it.luc.edu internet address = 184.108.40.206
(Again, we show only one of several
luc.edu nameservers). We continue.
# nslookup -query=ns - -norecurse 220.127.116.11 > intronetworks.cs.luc.edu ... Authoritative answers can be found from: cs.luc.edu nameserver = dns1.cs.luc.edu. ns1.cs.luc.edu internet address = 18.104.22.168
We now ask this last nameserver, for the
cs.luc.edu zone, for the A record:
# nslookup -query=A -norecurse - 22.214.171.124 > intronetworks.cs.luc.edu ... intronetworks.cs.luc.edu canonical name = linode1.cs.luc.edu. Name: linode1.cs.luc.edu Address: 126.96.36.199
Here we get a canonical name, or CNAME, record. The server that hosts
intronetworks.cs.luc.edu also hosts several other websites, with different names; for example, introcs.cs.luc.edu (at least as of 2015). This is known as virtual hosting. Rather than provide separate A records for each website name, DNS was set up to provide a
CNAME record for each website name pointing to a single physical server name
linode1.cs.luc.edu. Only one A record is then needed, for this server.
nslookup request for an A record returned instead the CNAME record, together with the A record for that CNAME (this is the 188.8.131.52 above). This is done for convenience.
Finally, note that the IPv4 address here, 184.108.40.206, is unrelated to Loyola’s own IPv4 address block 220.127.116.11/16. The server
linode1.cs.luc.edu is managed by an external provider; there is no connection between the DNS name hierarchy and the IP address hierarchy.
7.8.2 Other DNS Records¶
Besides address lookups, DNS also supports a few other kinds of searches. The best known is probably reverse DNS, which takes an IP address and returns a name. This is slightly complicated by the fact that one IP address may be associated with multiple DNS names. What DNS does in this case is to return the canonical name, or CNAME; a given address can have only one CNAME.
Given an IPv4 address, say 18.104.22.168, the idea is to reverse it and append to it the suffix
There is a DNS name hierarchy for names of this form, with zones and authoritative servers. If all this has been configured – which it often is not, especially for user workstations – a request for the PTR record corresponding to the above should return a DNS hostname. In the case above, the name luc.edu is returned.
DNS also supports MX, or Mail eXchange, records, meant to map a domain name (which originally might not correspond to any hostname, and which today is likely to correspond to the name of a web server) to the hostname of a server that accepts email on behalf of the domain. In effect this allows an organization’s domain name, eg
luc.edu, to represent both a web server and, at a different IP address, an email server.
The DNS Security Extensions, DNSSEC, make it possible for authoritative nameservers to provide authenticated responses to DNS queries, by using digital signatures (21.9 Public-Key Encryption). DNSSEC defines several additional DNS record types; see RFC 3833, RFC 4033 and, for the new record types, RFC 4034.
RFC 6891 outlines a framework for extensions to DNS, including new record types.
7.9 Address Resolution Protocol: ARP¶
If a host or router A finds that the destination IP address D = DIP matches the network address of one of its interfaces, it is to deliver the packet via the LAN. This means looking up the LAN address DLAN corresponding to DIP. How does it do this?
One approach would be via a special server, but the spirit of early IPv4 development was to avoid such servers, for both cost and reliability issues. Instead, the Address Resolution Protocol (ARP) is used. This is our first protocol that takes advantage of the existence of LAN-level broadcast; on LANs without physical broadcast (such as ATM), some other mechanism (usually involving a server) must be used.
The basic idea of ARP is that the host A sends out a broadcast ARP query or “who-has DIP?” request, which includes A’s own IPv4 and LAN addresses. All hosts on the LAN receive this message. The host for whom the message is intended, D, will recognize that it should reply, and will return an ARP reply or “is-at” message containing DLAN. Because the original request contained ALAN, D’s response can be sent directly to A, that is, unicast.
Additionally, all hosts maintain an ARP cache, consisting of (IPv4,LAN) address pairs for other hosts on the network. After the exchange above, A has (DIP,DLAN) in its table; anticipating that A will soon send it a packet to which it needs to respond, D also puts (AIP,ALAN) into its cache.
ARP-cache entries eventually expire. The timeout interval used to be on the order of 10 minutes, but linux systems now use a much smaller timeout (~30 seconds observed in 2012).
Somewhere along the line, and probably related to this shortened timeout interval, repeat ARP queries about a timed-out entry are first sent unicast, not broadcast, to the previous Ethernet address on record. This cuts down on the total amount of broadcast traffic; LAN broadcasts are, of course, still needed for new hosts. The ARP cache on a linux system can be examined with the command
ip -s neigh; the corresponding windows command is
The above protocol is sufficient, but there is one further point. When A sends its broadcast “who-has D?” ARP query, all other hosts C check their own cache for an entry for A. If there is such an entry (that is, if AIP is found there), then the value for ALAN is updated with the value taken from the ARP message; if there is no pre-existing entry then no action is taken. This update process serves to avoid stale ARP-cache entries, which can arise is if a host has had its Ethernet interface replaced. (Note that USB Ethernet interfaces can be replaced very quickly.)
7.9.1 ARP Finer Points¶
Most hosts today implement self-ARP, or gratuitous ARP, on startup (or wakeup): when station A starts up it sends out an ARP query for itself: “who-has A?”. Two things are gained from this: first, all stations that had A in their cache are now updated with A’s most current ALAN address, in case there was a change, and second, if an answer is received, then presumably some other host on the network has the same IPv4 address as A.
Self-ARP is thus the traditional IPv4 mechanism for duplicate address detection. Unfortunately, it does not always work as well as might be hoped; often only a single self-ARP query is sent, and if a reply is received then frequently the only response is to log an error message; the host may even continue using the duplicate address! If the duplicate address was received via DHCP, below, then the host is supposed to notify its DHCP server of the error and request a different IPv4 address.
RFC 5227 has defined an improved mechanism known as Address Conflict Detection, or ACD. A host using ACD sends out three ARP queries for its new IPv4 address, spaced over a few seconds and leaving the ARP field for the sender’s IPv4 address filled with zeroes. This last step means that any other host with that IPv4 address in its cache will ignore the packet, rather than update its cache. If the original host receives no replies, it then sends out two more ARP queries for its new address, this time with the ARP field for the sender’s IPv4 address filled in with the new address; this is the stage at which other hosts on the network will make any necessary cache updates. Finally, ACD requires that hosts that do detect a duplicate address must discontinue using it.
It is also possible for other stations to answer an ARP query on behalf of the actual destination D; this is called proxy ARP. An early common scenario for this was when host C on a LAN had a modem connected to a serial port. In theory a host D dialing in to this modem should be on a different subnet, but that requires allocation of a new subnet. Instead, many sites chose a simpler arrangement. A host that dialed in to C’s serial port might be assigned IP address DIP, from the same subnet as C. C would be configured to route packets to D; that is, packets arriving from the serial line would be forwarded to the LAN interface, and packets sent to CLAN addressed to DIP would be forwarded to D. But we also have to handle ARP, and as D is not actually on the LAN it will not receive broadcast ARP queries. Instead, C would be configured to answer on behalf of D, replying with (DIP,CLAN). This generally worked quite well.
Proxy ARP is also used in Mobile IP, for the so-called “home agent” to intercept traffic addressed to the “home address” of a mobile device and then forward it (eg via tunneling) to that device. See 7.13 Mobile IP.
One delicate aspect of the ARP protocol is that stations are required to respond to a broadcast query. In the absence of proxies this theoretically should work quite well: there should be only one respondent. However, there were anecdotes from the Elder Days of networking when a broadcast ARP query would trigger an avalanche of responses. The protocol-design moral here is that determining who is to respond to a broadcast message should be done with great care. (RFC 1122 section 3.2.2 addresses this same point in the context of responding to broadcast ICMP messages.)
ARP-query implementations also need to include a timeout and some queues, so that queries can be resent if lost and so that a burst of packets does not lead to a burst of queries. A naive ARP algorithm without these might be:
To send a packet to destination DIP, see if DIP is in the ARP cache. If it is, address the packet to DLAN; if not, send an ARP query for D
To see the problem with this approach, imagine that a 32KB packet arrives at the IP layer, to be sent over Ethernet. It will be fragmented into 22 fragments (assuming an Ethernet MTU of 1500 bytes), all sent at once. The naive algorithm above will likely send an ARP query for each of these. What we need instead is something like the following:
To send a packet to destination DIP:If DIP is in the ARP cache, send to DLAN and returnIf not, see if an ARP query for DIP is pending.If it is, put the current packet in a queue for D.If there is no pending ARP query for DIP, start one,again putting the current packet in the (new) queue for D
We also need:
If an ARP query for some CIP times out, resend it (up to a point)If an ARP query for CIP is answered, send off any packets in C’s queue
7.9.2 ARP Security¶
Suppose A wants to log in to secure server S, using a password. How can B (for Bad) impersonate S?
Here is an ARP-based strategy, sometimes known as ARP Spoofing. First, B makes sure the real S is down, either by waiting until scheduled downtime or by launching a denial-of-service attack against S.
When A tries to connect, it will begin with an ARP “who-has S?”. All B has to do is answer, “S is-at B”. There is a trivial way to do this: B simply needs to set its own IP address to that of S.
A will connect, and may be convinced to give its password to B. B now simply responds with something plausible like “backup in progress; try later”, and meanwhile use A’s credentials against the real S.
This works even if the communications channel A uses is encrypted! If A is using the SSH protocol (21.10.1 SSH), then A will get a message that the other side’s key has changed (B will present its own SSH key, not S’s). Unfortunately, many users (and even some IT departments) do not recognize this as a serious problem. Some organizations – especially schools and universities – use personal workstations with “frozen” configuration, so that the filesystem is reset to its original state on every reboot. Such systems may be resistant to viruses, but in these environments the user at A will always get a message to the effect that S’s credentials are not known.
7.9.3 ARP Failover¶
Suppose you have two front-line servers, A and B (B for Backup), and you want B to be able to step in if A freezes. There are a number of ways of achieving this, but one of the simplest is known as ARP Failover. First, we set AIP = BIP, but for the time being B does not use the network so this duplication is not a problem. Then, once B gets the message that A is down, it sends out an ARP query for AIP, including BLAN as the source LAN address. The gateway router, which previously would have had (AIP,ALAN) in its ARP cache, updates this to (AIP,BLAN), and packets that had formerly been sent to A will now go to B. As long as B is trafficking in stateless operations (eg html), B can pick up right where A left off.
7.9.4 Detecting Sniffers¶
Finally, here is an interesting use of ARP to detect Ethernet password sniffers (generally not quite the issue it once was, due to encryption and switching). To find out if a particular host A is in promiscuous mode, send an ARP “who-has A?” query. Address it not to the broadcast Ethernet address, though, but to some nonexistent Ethernet address.
If promiscuous mode is off, A’s network interface will ignore the packet. If promiscuous mode is on, A’s network interface will pass the ARP request to A itself, which is likely then to answer it.
Alas, linux kernels reject at the ARP-software level ARP queries to physical Ethernet addresses other than their own. However, they do respond to faked Ethernet multicast addresses, such as ff:ff:ff:00:00:00 or ff:ff:ff:ff:ff:fe.
7.9.5 ARP and multihomed hosts¶
If host A has two interfaces
iface2 on the same LAN, with respective IP addresses A1 and A2, then it is common for the two to be used interchangeably. Traffic addressed to A1 may be received via
iface2 and vice-versa, and traffic from A1 may be sent via
iface2. In RFC 1122, §22.214.171.124 this is known as the weak end-system model; the idea is that we should think of the IP addresses A1 and A2 as bound to A rather than to their respective interfaces.
In support of this model, ARP can usually be configured (in fact this is often the default) so that ARP requests for either IP address and received by either interface may be answered with either physical address. Usually all requests are answered with the physical address of the preferred (ie faster) interface.
As an example, suppose A has an Ethernet interface
eth0 with IP address 10.0.0.2 and a faster Wi-Fi interface
wlan0 with IP address 10.0.0.3 (although Wi-Fi interfaces are not always faster). In this setting, an ARP request “who-has 10.0.0.2” would be answered with
wlan0‘s physical address, and so all traffic to A, to either IP address, would arrive via
eth0 interface would go essentially unused. Similarly, though not due to ARP, traffic sent by A with source address 10.0.0.2 might depart via
This situation is on linux systems adjusted by changing
The alternative, in which the two interfaces are kept strictly separate, is the strong end-system model.
7.10 Dynamic Host Configuration Protocol (DHCP)¶
DHCP is the most common mechanism by which hosts are assigned their IPv4 addresses. DHCP started as a protocol known as Reverse ARP (RARP), which evolved into BOOTP and then into its present form. It is documented in RFC 2131. Recall that ARP is based on the idea of someone broadcasting an ARP query for a host, containing the host’s IPv4 address, and the host answering it with its LAN address. DHCP involves a host, at startup, broadcasting a query containing its own LAN address, and having a server reply telling the host what IPv4 address is assigned to it, hence the “Reverse ARP” name.
The DHCP response message is also likely to carry, piggybacked onto it, several other essential startup options. Unlike the IPv4 address, these additional network parameters usually do not depend on the specific host that has sent the DHCP query; they are likely constant for the subnet or even the site. In all, a typical DHCP message includes the following:
- IPv4 address
- subnet mask
- default router
- DNS Server
These four items are a standard minimal network configuration; in practical terms, hosts cannot function properly without them. Most DHCP implementations support the piggybacking of the latter three above, and a wide variety of other configuration values, onto the server responses.
The DHCP server has a range of IPv4 addresses to hand out, and maintains a database of which IPv4 address has been assigned to which LAN address. Reservations can either be permanent or dynamic; if the latter, hosts typically renew their DHCP reservation periodically (typically one to several times a day).
7.10.1 NAT, DHCP and the Small Office¶
If you have a large network, with multiple subnets, a certain amount of manual configuration is inevitable. What about, however, a home or small office, with a single line from an ISP? A combination of NAT (7.7 Network Address Translation) and DHCP has made autoconfiguration close to a reality.
The typical home/small-office “router” is in fact a NAT router (7.7 Network Address Translation) coupled with an Ethernet switch, and usually also coupled with a Wi-Fi access point and a DHCP server. In this section, we will use the term “NAT router” to refer to this whole package. One specially designated port, the external port, connects to the ISP’s line, and uses DHCP as a client to obtain an IPv4 address for that port. The other, internal, ports are connected together by an Ethernet switch; these ports as a group are connected to the external port using NAT translation. If wireless is supported, the wireless side is connected directly to the internal ports.
Isolated from the Internet, the internal ports can thus be assigned an arbitrary non-public IPv4 address block, eg 192.168.0.0/24. The NAT router typically contains a DCHP server, usually enabled by default, that will hand out IPv4 addresses to everything connecting from the internal side.
Generally this works seamlessly. However, if a second NAT router is also connected to the network (sometimes attempted to extend Wi-Fi range, in lieu of a commercial Wi-Fi repeater), one then has two operating DHCP servers on the same subnet. This often results in chaos, though is easily fixed by disabling one of the DHCP servers.
While omnipresent DHCP servers have made IPv4 autoconfiguration work “out of the box” in many cases, in the era in which IPv4 was designed the need for such servers would have been seen as a significant drawback in terms of expense and reliability. IPv6 has an autoconfiguration strategy (8.7.2 Stateless Autoconfiguration (SLAAC)) that does not require DHCP, though DHCPv6 may well end up displacing it.
7.10.2 DHCP and Routers¶
It is often desired, for larger sites, to have only one or two DHCP servers, but to have them support multiple subnets. Classical DHCP relies on broadcast, which isn’t forwarded by routers, and even if it were, the DHCP server would have no way of knowing on what subnet the host in question was actually located.
This is generally addressed by DHCP Relay (sometimes still known by the older name BOOTP Relay). The router (or, sometimes, some other node on the subnet) receives the DHCP broadcast message from a host, and notes the subnet address of the arrival interface. The router then relays the DHCP request, together with this subnet address, to the designated DHCP Server; this relayed message is sent directly (unicast), not broadcast. Because the subnet address is included, the DHCP server can figure out the correct IPv4 address to assign.
This feature has to be specially enabled on the router.
7.11 Internet Control Message Protocol¶
The Internet Control Message Protocol, or ICMP, is a protocol for sending IP-layer error and status messages; it is defined in RFC 792. ICMP is, like IP, host-to-host, and so they are never delivered to a specific port, even if they are sent in response to an error related to something sent from that port. In other words, individual UDP and TCP connections do not receive ICMP messages, even when it would be helpful to get them.
ICMP messages are identified by an 8-bit type field, followed by an 8-bit subtype, or code. Here are the more common ICMP types, with subtypes listed in the description.
|Destination Unreachable||Destination network unreachable|
|Destination host unreachable|
|Destination port unreachable|
|Fragmentation required but DF flag set|
|Network administratively prohibited|
|Source Quench||Congestion control|
|Redirect Message||Redirect datagram for the network|
|Redirect datagram for the host|
|Redirect for TOS and network|
|Redirect for TOS and host|
|Router Solicitation||Router discovery/selection/solicitation|
|Time Exceeded||TTL expired in transit|
|Fragment reassembly time exceeded|
|Bad IP Header or Parameter||Pointer indicates the error|
|Missing a required option|
|Timestamp Timestamp Reply||Like
ICMP is perhaps best known for Echo Request/Reply, on which the
ping tool (1.14 Some Useful Utilities) is based. Ping remains very useful for network troubleshooting: if you can ping a host, then the network is reachable, and any problems are higher up the protocol chain. Unfortunately, ping replies are often blocked by many firewalls, on the theory that revealing even the existence of computers is a security risk. While this may sometimes be an appropriate decision, it does significantly impair the utility of ping.
Ping can be asked to include IP timestamps (7.1 The IPv4 Header) on linux systems with the
-T option, and on Windows with
Source Quench was used to signal that congestion has been encountered. A router that drops a packet due to congestion experience was encouraged to send ICMP Source Quench to the originating host. Generally the TCP layer would handle these appropriately (by reducing the overall sending rate), but UDP applications never receive them. ICMP Source Quench did not quite work out as intended, and was formally deprecated by RFC 6633. (Routers can inform TCP connections of impending congestion by using the ECN bits.)
The Destination Unreachable type has a large number of subtypes:
- Network unreachable: some router had no entry for forwarding the packet, and no default route
- Host unreachable: the packet reached a router that was on the same LAN as the host, but the host failed to respond to ARP queries
- Port unreachable: the packet was sent to a UDP port on a given host, but that port was not open. TCP, on the other hand, deals with this situation by replying to the connecting endpoint with a
resetpacket. Unfortunately, the UDP Port Unreachable message is sent to the host, not to the application on that host that sent the undeliverable packet, and so is close to useless as a practical way for applications to be informed when packets cannot be delivered.
- Fragmentation required but DF flag set: a packet arrived at a router and was too big to be forwarded without fragmentation. However, the Don’t Fragment bit in the IPv4 header was set, forbidding fragmentation.
- Administratively Prohibited: this is sent by a router that knows it can reach the network in question, but has configureintro to drop the packet and send back Administratively Prohibited messages. A router can also be configured to blackhole messages: to drop the packet and send back nothing.
In 12.12 Path MTU Discovery we will see how TCP uses the ICMP message Fragmentation required but DF flag set as part of Path MTU Discovery, the process of finding the largest packet that can be sent to a specific destination without fragmentation. The basic idea is that we set the DF bit on some of the packets we send; if we get back this message, that packet was too big.
Some sites and firewalls block ICMP packets in addition to Echo Request/Reply, and for some messages one can get away with this with relatively few consequences. However, blocking Fragmentation required but DF flag set has the potential to severely affect TCP connections, depending on how Path MTU Discovery is implemented, and thus is not recommended. If ICMP filtering is contemplated, it is best to base block/allow decisions on the ICMP type, or even on the type and code. For example, most firewalls support rule sets of the form “allow ICMP destination-unreachable; block all other ICMP”.
The Timestamp option works something like Echo Request/Reply, but the receiver includes its own local timestamp for the arrival time, with millisecond accuracy. See also the IP Timestamp option, 7.1 The IPv4 Header, which appears to be more frequently used.
The type/code message format makes it easy to add new ICMP types. Over the years, a significant number of additional such types have been defined; a complete list is maintained by the IANA. Several of these later ICMP types were seldom used and eventually deprecated, many by RFC 6918.
ICMP packets are usually forwarded correctly through NAT routers, though due to the absence of port numbers the router must do a little more work. RFC 3022 and RFC 5508 address this. For ICMP “queries”, like ping, the ICMP Query Identifier field can be used to recognize the returning response. ICMP “error” messages – basically everything else in the table above – are a little trickier, because there is no direct connection between the inbound error message and any of the previous outbound non-ICMP packets that triggered the response. However, the headers of the packet that triggered the ICMP error message are embedded in the body of the ICMP message. The NAT router can look at those embedded headers to determine how to forward the ICMP message (the NAT router must also rewrite the addresses of those embedded headers).
7.11.1 Traceroute and Time Exceeded¶
The traceroute program uses ICMP Time Exceeded messages. A packet is sent to the destination (often UDP to an unused port), with the TTL set to 1. The first router the packet reaches decrements the TTL to 0, drops it, and returns an ICMP Time Exceeded message. The sender now knows the first router on the chain. The second packet is sent with TTL set to 2, and the second router on the path will be the one to return ICMP Time Exceeded. This continues until finally the remote host returns something, likely ICMP Port Unreachable.
For an example of traceroute output, see 1.14 Some Useful Utilities. In that example, the three traceroute probes for the Nth router are sometimes answered by two or even three different routers; this suggests routers configured to work in parallel rather than route changes.
Many routers no longer respond with ICMP Time Exceeded messages when they drop packets. For the distance value corresponding to such a router, traceroute reports
Traceroute assumes the path does not change. This is not always the case, although in practice it is seldom an issue.
Traceroute to a nonexistent site works up to the point when the packet reaches the Internet “backbone”: the first router which does not have a default route. At that point the packet is not routed further (and an ICMP Destination Network Unreachable should be returned).
Most non-router hosts start up with an IPv4 forwarding table consisting of a single (default) router, discovered along with their IPv4 address through DHCP. ICMP Redirect messages help hosts learn of other useful routers. Here is a classic example:
A is configured so that its default router is R1. It addresses a packet to B, and sends it to R1. R1 receives the packet, and forwards it to R2. However, R1 also notices that R2 and A are on the same network, and so A could have sent the packet to R2 directly. So R1 sends an appropriate ICMP redirect message to A (“Redirect Datagram for the Network”), and A adds a route to B via R2 to its own forwarding table.
7.11.3 Router Solicitation¶
These ICMP messages are used by some router protocols to identify immediate neighbors. When we look at routing-update algorithms, below, these are where the process starts.
7.12 Unnumbered Interfaces¶
We mentioned in 1.10 IP - Internet Protocol and 7.2 Interfaces that some devices allow the use of point-to-point IP links without assigning IP addresses to the interfaces at the ends of the link. Such IP interfaces are referred to as unnumbered; they generally make sense only on routers. It is a firm requirement that the node (ie router) at each endpoint of such a link has at least one other interface that does have an IP address; otherwise, the node in question would be anonymous, and could not participate in the router-to-router protocols of 9 Routing-Update Algorithms.
The diagram below shows a link L joining routers R1 and R2, which are connected to subnets 126.96.36.199/24 and 188.8.131.52/24 respectively. The endpoint interfaces of L, both labeled
link0, are unnumbered.
The endpoints of L could always be assigned private IPv4 addresses (7.3 Special Addresses), such as 10.0.0.1 and 10.0.0.2. To do this we would need to create a subnet; because the host bits cannot be all 0’s or all 1’s, the minimum subnet size is four (eg 10.0.0.0/30). Furthermore, the routing protocols to be introduced in 9 Routing-Update Algorithms will distribute information about the subnet throughout the organization or “routing domain”, meaning care must be taken to ensure that each link’s subnet is unique. Use of unnumbered links avoids this.
If R1 were to originate a packet to be sent to (or forwarded via) R2, the standard strategy is for it to treat its
link0 interface as if it shared the IP address of its Ethernet interface
eth0, that is, 184.108.40.206; R2 would do likewise. This still leaves R1 and R2 violating the IP local-delivery rule of 7.5 The Classless IP Delivery Algorithm; R1 is expected to deliver packets via local delivery to 220.127.116.11 but has no interface that is assigned an IP address on the destination subnet 18.104.22.168/24. The necessary dispensation, however, is granted by RFC 1812. All that is necessary by way of configuration is that R1 be told R2 is a directly connected neighbor reachable via its
link0 interface. On linux systems this might be done with the
ip route command on R1 as follows:
ip route add 22.214.171.124 dev link0
Because L is a point-to-point link, there is no destination LAN address and thus no ARP query.
7.13 Mobile IP¶
In the original IPv4 model, there was a strong if implicit assumption that each IP host would stay put. One role of an IPv4 address is simply as a unique endpoint identifier, but another role is as a locator: some prefix of the address (eg the network part, in the class-A/B/C strategy, or the provider prefix) represents something about where the host is physically located. Thus, if a host moves far enough, it may need a new address.
When laptops are moved from site to site, it is common for them to receive a new IP address at each location, eg via DHCP as the laptop connects to the local Wi-Fi. But what if we wish to support devices like smartphones that may remain active and communicating while moving for thousands of miles? Changing IP addresses requires changing TCP connections; life (and application development) might be simpler if a device had a single, unchanging IP address.
One option, commonly used with smartphones connected to some so-called “3G” networks, is to treat the phone’s data network as a giant wireless LAN. The phone’s IP address need not change as it moves within this LAN, and it is up to the phone provider to figure out how to manage LAN-level routing, much as is done in 126.96.36.199 Wi-Fi Roaming.
But Mobile IP is another option, documented in RFC 5944. In this scheme, a mobile host has a permanent home address and, while roaming about, will also have a temporary care-of address, which changes from place to place. The care-of address might be, for example, an IP address assigned by a local Wi-Fi network, and which in the absence of Mobile IP would be the IP address for the mobile host. (This kind of care-of address is known as “co-located”; the care-of address can also be associated with some other device – known as a foreign agent – in the vicinity of the mobile host.) The goal of Mobile IP is to make sure that the mobile host is always reachable via its home address.
To maintain connectivity to the home address, a Mobile IP host needs to have a home agent back on the home network; the job of the home agent is to maintain an IP tunnel that always connects to the device’s current care-of address. Packets arriving at the home network addressed to the home address will be forwarded to the mobile device over this tunnel by the home agent. Similarly, if the mobile device wishes to send packets from its home address – that is, with the home address as IP source address – it can use the tunnel to forward the packet to the home agent.
The home agent may use proxy ARP (7.9.1 ARP Finer Points) to declare itself to be the appropriate destination on the home LAN for packets addressed to the home (IP) address; it is then straightforward for the home agent to forward the packets.
An agent discovery process is used for the mobile host to decide whether it is mobile or not; if it is, it then needs to notify its home agent of its current care-of address.
7.13.1 IP-in-IP Encapsulation¶
There are several forms of packet encapsulation that can be used for Mobile IP tunneling, but the default one is IP-in-IP encapsulation, defined in RFC 2003. In this process, the entire original IP packet (with header addressed to the home address) is used as data for a new IP packet, with a new IP header (the “outer” header) addressed to the care-of address.
A value of 4 in the outer-IP-header
Protocol field indicates that IPv4-in-IPv4 tunneling is being used, so the receiver knows to forward the packet on using the information in the inner header. The MTU of the tunnel will be the original MTU of the path to the care-of address, minus the size of the outer header. A very similar mechanism is used for IPv6-in-IPv4 encapsulation (that is, with IPv6 in the inner packet), except that the outer IPv4
Protocol field value is now 41. See 8.13 IPv6 Connectivity via Tunneling.
IP-in-IP encapsulation presents some difficulties for NAT routers. If two hosts A and B behind a NAT router send out encapsulated packets, the packets may differ only in the source IP address. The NAT router, upon receiving responses, doesn’t know whether to forward them to A or to B. One partial solution is for the NAT router to support only one inside host sending encapsulated packets. If the NAT router knew that encapsulation was being used for Mobile IP, it might look at the home address in the inner header to determine the correct home agent to which to deliver the packet, but this is a big assumption. A fuller solution is outlined in RFC 3519.
At this point we have concluded the basic mechanics of IPv4. Still to come is a discussion of how IP routers build their forwarding tables. This turns out to be a complex topic, divided into routing within single organizations and ISPs – 9 Routing-Update Algorithms – and routing between organizations – 10 Large-Scale IP Routing.
But before that, in the next chapter, we compare IPv4 with IPv6, now twenty years old but still seeing limited adoption. The biggest issue fixed by IPv6 is IPv4’s lack of address space, but there are also several other less dramatic improvements.
Exercises are given fractional (floating point) numbers, to allow for interpolation of new exercises. Exercise 6.5 is distinct, for example, from exercises 6.0 and 7.0. Exercises marked with a ♢ have solutions or hints at 23.7 Solutions for IPv4.
1.0. Suppose an Ethernet packet represents a TCP acknowledgment; that is, the packet contains an IPv4 header and a 20-byte TCP header but nothing else. Is the IPv4 packet here smaller than the Ethernet minimum-packet size, and, if so, by how much?
2.0. How can a receiving host tell if an arriving IPv4 packet is unfragmented? Hint: such a packet will be both the “first fragment” and the “last fragment”.
3.0. How long will it take the IDENT field of the IPv4 header to wrap around, if the sender host A sends a stream of packets to host B as fast as possible? Assume the packet size is 1500 bytes and the bandwidth is 600 Mbps.
4.0. The following diagram has routers A, B, C, D and E; E is the “border router” connecting the site to the Internet. All router-to-router connections are via Ethernet-LAN /24 subnets with addresses of the form 200.0.x. Give forwarding tables for each of A♢, B, C and D. Each table should include each of the listed subnets and also a default entry that routes traffic toward router E. Directly connected subnets may be listed with a next_hop of “direct”.
200.0.5────A────200.0.6────B────200.0.7────D────200.0.8────E────Internet │ 200.0.9 │ C │ 200.0.10
5.0. (This exercise is an attempt at modeling Internet-2 routing.) Suppose sites S1 ... Sn each have a single connection to the standard Internet, and each site Si has a single IPv4 address block Ai. Each site’s connection to the Internet is through a single router Ri; each Ri‘s default route points towards the standard Internet. The sites also maintain a separate, higher-speed network among themselves; each site has a single link to this separate network, also through Ri. Describe what the forwarding tables on each Ri will have to look like so that traffic from one Si to another will always use the separate higher-speed network.
6.0. For each IPv4 network prefix given (with length), identify which of the subsequent IPv4 addresses are part of the same subnet.
6.5. Convert the following subnet masks to /k notation, and vice-versa:
7.0. Suppose that the subnet bits below for the following five subnets A-E all come from the beginning of the fourth byte of the IPv4 address; that is, these are subnets of a /24 block.
- A: 00
- B: 01
- C: 110
- D: 111
- E: 1010
8.0. In 7.9 Address Resolution Protocol: ARP it was stated that, in newer implementations, “repeat ARP queries about a timed out entry are first sent unicast”, in order to reduce broadcast traffic. What would have to happen to create a situation where the repeated unicast query for a given IP address fails, but a followup broadcast query for that same IP address succeeds?
9.0. Suppose A broadcasts an ARP query “who-has B?”, receives B’s response, and proceeds to send B a regular IPv4 packet. If B now wishes to reply, why is it likely that A will already be present in B’s ARP cache? Identify a circumstance under which this can fail.
10.0. Suppose A broadcasts an ARP request “who-has B”, but inadvertently lists the physical address of another machine C instead of its own (that is, A’s ARP query has IPsrc = A, but LANsrc = C). What will happen? Will A receive a reply? Will any other hosts on the LAN be able to send to A? What entries will be made in the ARP caches on A, B and C?
11.0. Suppose host A connects to the Internet via Wi-Fi. The default router is RW. Host A now begins exchanging packets with a remote host B: A sends to B, B replies, etc. The exact form of the connection does not matter, except that TCP may not work.